Ocean Pearl Finish
Description : A single pack Pearl Coating manufactured to stringent U.K. testing procedures, based on modern resins and having a plastic like appearance.
Product Features &
Recommended Uses : Ocean Pearl Finish has a Glossy Appearance for greater wash-ability and resistance to soiling. can be applied to almost any surface where hard wearing attractive decoration is required. Applied by one simple operation and if damaged, can be “touched up” locally to blend without being apparent.
Pearl is antistatic and does not attract airborne dust thereby reducing the cost of maintenance and thus contributing to hygiene.Volume Solids : 21%
P. H. : 7 – 8
Film Thickness : Wet Microns 190
Dry Microns 40
Theoretical Coverage : 6 SQMT/ LiterNote: The information in this data sheet was correct at the time of print. We can not accept any responsibility for conditions beyond our control
Standard Glaze
Product : STD. GLAZE
Type : Water based, clear acrylic lacquer.
Application : Can be applied by brush, roller or sprayed.
Recommended Uses : As a top coat to give an extra protection and a glossy finish.
Features : 86 to 92 Ku at 30 Cْ
Specific Gravity : 1.00
Spreading Rate: 5 – 8 Sq. Meters per Liter.
Drying Time : One hour, depending on the ambient temperature conditions.
Application : Can be applied by brush, roller
Note : Above information are true to the best of our knowledge and subjected to change without prior notice.
Textured Coat
Product : A high quality decorative textured coating for interior use that can be applied in a variety of ways to produce effective finishes.
Recommended Use : Concrete, Gypsum, Wood and well prepared walls.
Specific Gravity : 1.7
Volume Solids : 65%
Flash Point : Non-flammable.
Theoretical spreading Rate : 1.5-2 Square Meter per liter, depending
on desired texture.
Application : By sponge roller, wire comb, texture gun,
Patterned roller.
Surface preparation : The surface must be clean, and free of all loose particles, by the use of stiff bristle brushes. Tex primer should be used on new surfaces.
Colors : White, but can be tinted on special request.
Mixing Ratio : Single pack.
Thinner / Cleaner : Water.
Drying time : 2 Hrs.
Recommended Coating System:
1st Coat : Sealer White or Tex Primer.
2nd Coat : Textured Coat.
Note : The information given is based on our laboratory tests, given in good faith. However, since the conditions and methods of the use of the products are beyond our control, we can only guarantee the quality of the product.
Storage and Handling : The product should be kept in a cool and well ventilated place, protected from heat and direct sunlight. Containers must be kept tightly closed.Stucco Putty/Wall Putty
Type : An Styrene Acrylic Emulsion based Putty.
Use : As a Putty, It can be used for Interior and Exterior surface like Plaster concrete, Walls, etc and in filling for small cracks, holes of surface for making the perfect Surface.
Important Features : 1. Very smooth and easy application.
2. Non sagging and excellent adhesive strength.
3. It gives leveled surface suitable for subsequent coat.
Technical Information
Appearance
Viscosity : Paste
Density: 1.69 ± 0.03 Kg /Lit.
Color : White
Spreading Rate : 05–07 SqM. / Ltrs
Solid by volume : 60%
Dry Film Thickness : 100 Microns/ per coat
Dry : 1 – 2 Hours
Through Dry Finish : 5 – 6 Hours
Flash Point : Smooth, Matt
Over Coat : THIXOTROPIC
: Non Flammable
: After 8 Hours
Shelf Life : Two Years in original sealed drums.
Storage : Under Shade. Keep away from direct Sun Light and freezing Condition, clean, cool and dry place.
Recommended System : The surface should be sound dry and clean and free from dirt, oil grease and other loose paints. Remove old cracked film of paint and other. Surface must be clean and dry before application. After full preparation of surface , apply one coat of INTER PRIMER SEALER, then apply INTER WALL PUTTY two coats, after drying sand the Putty and clean the surface for subsequent coats
Application : By stainless steel putty knife or Spatula.
Thinner : Pure and clean water, Generally not required.
Precautions : Do not apply below 5 Deg. C and on wet condition. Ensure good ventilation during Application and avoid Breathing mist. Keep away from Children.
Safety : Follow the Standard Safety measures as required for Decorative Coating System
Note : Above information are true to the best of our knowledge and subjected to change without prior notice.Acrylic Primer Sealer
Type : An Styrene Acrylic Emulsion based Primer Sealer for all weather condition.
Use : General purpose water base Primer Sealer formulated for use as Primer Coat for Emulsion & Texture Paint to sealing the surface for better adhesion and preventing absorption of highly porous surface. It is suitable for Int. /Ext. surface like Plaster, Wall Concrete, Cement and Gypsum etc.
Important Features :1. Very good priming capacity.
2. Excellent adhesion and quick drying and very easy for application.
3. Very good flow and leveling properties.
4. High Alkali and Weather Resistance.
Technical Information
Appearance
Viscosity : 126 ± 10Ku at 30 Deg
Density: 1.54 ± 0.05 Kg /Lit.
Color : White
Spreading Rate : 10–12 Sq./Ltrs , depends upon the nature of Surface.
Solid by volume : 35%
Dry Film Thickness : 20 microns/ per coat
Dry : 1 – 2 Hours
Through Dry Finish : 2 Hours
Flash Point : Matt
Over Coat : THIXOTROPIC
: Non Flammable
: After 4 Hours
Shelf Life : One Year in Sealed drums.
Storage : Under Shade. Keep away from direct Sun Light and freezing Condition, clean, cool and dry place.
Surface Preparation : The surface should be sound dry and clean and free from dirt, oil grease and other loose paints.
Old Painted Surface : Remove old cracked film of paint and other.
New Surface : All loose dirt and powder and other contamination must be removed. Alkaline and Lime containing surface must be Flushing with pure water. Surface must be clean and dry before application. After full preparation of surface , Apply PRIMER SEALER for making the good surface for subsequent coat
Application : By Brush Roller or Spray Gun. Stir well before use.
Thinner : Pure and clean water.
Thinner Ratio : 10% to 15% by volume for Roller and Spray.
Precautions : Do not apply below 5 Deg. C and on wet condition. Ensure good ventilation during Application and avoid Breathing mist. Keep away from Children.
Safety : Follow the Standard Safety measures as required for Decorative Coating System
Note : Above information are true to the best of our knowledge and subjected to change without prior notice.
Classic Emulsion
Type : An Styrene Acrylic Emulsion base Emulsion Paint for Interior use.
Use : Interior Emulsion Paint suitable for Interior surface like Plaster, Wall and Ceilings, Cement, Block Works etc.
Important Features :
1. Excellent hiding power and adhesion strength.
2. Very good flow and leveling properties.
3. Easy application and Fast Drying Properties.
Technical Information
Appearance
Viscosity : 126 ± 10Ku at 30 Deg
Density: 1.55 ± 0.03 Kg /Lit.
Color : White or Color
Spreading Rate : 07–08 Sq./Ltrs , depends upon the nature of Surface.
Solid by volume : 48%
Dry Film Thickness : 30 microns/ per coat
Surface Dry : 1/2 Hours
Through Dry Finish : 2 Hours
Flash Point : Matt
Over Coat : THIXOTROPIC
: Non Flammable
: After 4 Hours
Shelf Life : One Year in Sealed drums.
Storage : Under Shade. Keep away from direct Sun Light and freezing Condition, clean, cool and dry place.
Surface Preparation : The surface should be sound dry and clean and free from dirt, oil grease and other loose paints.
Old Painted Surface : Remove old cracked film of paint and other contamination like loose scales, dirt and grease. Prime the Surface to be painted with Primer Sealer. Fill the holes and cracks with Inter Wall Putty. After drying Sand the putty and clean the surface for final coats.
New Surface : All loose dirt and powder and other contamination must be removed. Alkaline and Lime containing surface must be Flushing with pure water. After full drying prime the Surface to be painted with Inter Primer Sealer. Fill the holes and cracks with Inter Wall Putty. After drying Sand the putty and clean the surface for subsequent coats. Apply two coats of Inter Lux Emulsion.
Application : By Brush, Roller or Spray. Stir well before use.
Thinner : Pure and clean water.
Thinner Ratio : 10% to 15% by volume for Roller, Brush and Spray Gun.
Precautions : Do not apply below 5 Deg. C and on wet condition. Ensure good ventilation during Application and avoid Breathing mist. Keep away from Children.
Safety : Follow the Standard Safety measures as required for Decorative Coating System
Note : Above information are true to the best of our knowledge and subjected to change without prior notice.
Acrylic Emulsion
Type : An Styrene Acrylic Emulsion base Emulsion Paint for Exterior use.
Use : Exterior Emulsion Paint suitable for Interior surface like Plaster, Wall, Ceilings, Cement, Block Works, Asbestos etc.
Important Features :
1. Excellent Al Kali and Weather Resistance.
2. Excellent hiding power and adhesion strength.
3. Very good flow and leveling properties.
4. Easy application and Fast Drying Properties.
Technical Information
Appearance
Viscosity : 126 ± 10Ku at 30 Deg
Density: 1.50 ± 0.05 Kg /Lit.
Color : White or Color
Spreading Rate : 09–10 Sq./Ltrs , depends upon the nature of Surface.
Solid by volume : 45%
Dry Film Thickness : 30 microns/ per coat
Surface Dry : 1Hours
Through Dry Finish : 2 Hours
Flash Point : Matt
Over Coat : THIXOTROPIC: Non Flammable
: After 4 Hours
Shelf Life : One Year in Sealed drums.
Storage : Under Shade. Keep away from direct Sun Light and freezing Condition, clean, cool and dry place.
Surface Preparation : The surface should be sound dry and clean and free from dirt, oil grease and other loose paints.
Old Painted Surface : Remove old cracked film of paint and other contamination like loose scales, dirt and grease. Prime the Surface to be painted with Inter Primer Sealer. Fill the holes and cracks with Inter Wall Putty. After drying Sand the putty and clean the surface for final coats.
New Surface : All loose dirt and powder and other contamination must be removed. Alkaline and Lime containing surface must be Flushing with pure water. After full drying prime the Surface to be painted with Inter Primer Sealer. Fill the holes and cracks with Inter Wall Putty. After drying Sand the putty and clean the surface for subsequent coats. Apply two coats of Acrylic Emulsion.
Application : By Brush, Roller or Spray. Stir well before use.
Thinner : Pure and clean water.
Thinner Ratio : 10% to 15% by volume for Roller, Brush and Spray Gun.
Precautions : Do not apply below 5 Deg. C and on wet condition. Ensure good ventilation during Application and avoid Breathing mist. Keep away from Children.
Safety : Follow the Standard Safety measures as required for Decorative Coating System
Note : Above information are true to the best of our knowledge and subjected to change without prior notice.
Inter Silk
Type : An Styrene Acrylic Emulsion based High Quality Gloss. Paint suitable for all weather conditions.
Use : High Quality Gloss Emulsion paint specially formulated for Int. / Ext. surface like Plaster, Wall, Cement, Bricks Work and Gypsum etc.
Important Features :
1. Excellent hiding power and high flexible.
2. Excellent covering and very good adhesion strength.
3. Very good flow and leveling properties.
4. High Alkali and Weather Resistance.
5. Very Smooth and Easy application.
Technical Information
Appearance
Viscosity : 126 ± 10Ku at 30 Deg
Density: 1.25 ± 0.05 Kg /Lit.
Color : White or Color
Spreading Rate : 10–12 Sq./Ltrs , depends upon the nature of Surface.
Solid by volume : 45%
Dry Film Thickness : 30 microns/ per coat
Surface Dry : 1 - 2 Hours
Through Dry Finish : 3 - 4 Hours
Flash Point : Glossy
Over Coat : THIXOTROPIC
: Non Flammable
: After 8 HoursShelf Life : One Year in Sealed drums.
Storage : Under Shade. Keep away from direct Sun Light and freezing Condition, clean, cool and dry place.
Surface Preparation : The surface should be sound dry and clean and free from dirt, oil grease and other loose paints.
Old Painted Surface : Remove old cracked film of paint and other.
New Surface : All loose dirt and powder and other contamination must be removed. Alkaline and Lime containing surface must be Flushing with pure water. After full drying prime the Surface to be painted with Inter Primer Sealer. Fill the holes and cracks with Inter Wall Putty. After drying Sand the putty and clean the surface for subsequent coats. Apply one coats of Inter Silk.
Application : By Brush, Roller or Spray. Stir well before use.
Thinner : Pure and clean water.
Thinner Ratio : 10% to 15% by volume for Roller , Brush and Spray Gun.
Precautions : Do not apply below 5 Deg. C and on wet condition. Ensure good ventilation during Application and avoid Breathing mist. Keep away from Children.
Safety : Follow the Standard Safety measures as required for Decorative Coating System
Note : Above information are true to the best of our knowledge and subjected to change without prior notice.
Inter Gloss Enamel
Product Description : Intergloss is an alkyd based, glossy.
Recommended Use : As a topcoat for exterior and interior use on Stee structures, Wood, Hardboard, Chipboard, M.D.F, and Concrete.
Colors : White, Black and as per the shade card.
Solids : 46.5% By Volume.
Specific Gravity : 1.07 KG/ Liter
Viscosity : 92-95 KU AT 30 DEG C
Drying Time : Dry to touch: 3 Hours (At 30 Deg C.)
Dry to recoat: 4 Hours
Tack free: 12 Hours.
Shelf Life : 9/12 Months.
Surface Preparation : The surface should be thoroughly clean. Depending on the substrate, in appropriate primer and undercoat should be used.
Application Data : By brush, Roller, Airless or Conventional spray.
Thinning : Thinning if using brush or roller: Up to 7%. Thinning if using 7-10%
Special Note : We cannot be responsible for conditions that are beyond our control, therefore, we can only guarantee the quality of the Product and not it's application.Acrylic Top Top (Thermo Plastic)
Type : A High Gloss Thermoplastic Resin based top coat.
Use : As a top coat on Interior and Exterior surface wall, cement, concrete, Gypsum, wood and steel surface etc., particularly as a top coat on Texture.
Important Features :
1. Excellent durability and scratch resistance.
2. Quick drying with excellent adhesion on approximately all surface.
3. Excellent weather resistance and good coverage.
4. Excellent gloss and color retention.
Technical Information
Appearance
Viscosity : 88 ± 10 K.U. at 30 Deg.
Density: 1.08 ± 0.03 Kg /Lit.
Color : White or Color
Spreading Rate : 10–12 SqM. / Ltrs Depending upon the surface.
Solid by volume : 43%
Dry Film Thickness : 30 Microns/ per coat
Dry : 1/2 Hours
Through Dry Finish : 2 Hours
Flash Point : High Gloss.
Over Coat : Liquid.: 27 Deg. C
: After 8 Hours
Shelf Life : One Years in original sealed drums.
Storage : Under Shade. Keep away from direct Sun Light and freezing Condition, clean, cool and dry place.
Recommended System : The surface should be sound dry and clean and free from dirt, oil grease and other loose paints. Remove old cracked film of paint and other. Surface must be clean and dry before application. If the porosity of the surface is high then apply the suitable coat of Primer. Then Apply Two Coats of Acrylic Top Coat.
(Not recommended on old Gloss Enamel Surface).
Application : By Roller, Brush, Spray. Stir well before use.
Thinner : Ocean Thinner.
Precautions : Do not apply below 5 Deg. C and on wet condition. Ensure good ventilation during Application and avoid Breathing mist. Keep away from Children.
Safety : Use Gloves, Mask during application.
Follow the Standard Safety measures as required for Decorative Coating System
Note: Above information are true to the best of our knowledge and subjected to change without prior notice.
Red Oxide Primer
Type : Synthetic Alkyd Resin based White Spirit Thinnable Primer For Iron & Steel.
Use : Red Oxide Primer used on Iron and Steel surface to provide the Excellent resistance to anti corrosive properties.
Important Features :1. Protect the Iron & Steel from corrosion.
2. Excellent flow and leveling properties.
3. Excellent Scratch resistance.
4. Fast drying and good covering power.
Technical Information
Appearance
Viscosity : 90 ± 20K.U at 30 ْc
Density: 1.55± 0.03 Kg /Ltr.
Color : Red
Spreading Rate : 12 – 14 Sq.m /Ltr.
Solid by volume : 55%
Dry Film Thickness : 40 microns/ per coat
Surface Dry : 1 - 2 Hours
Through Dry Finish : 4 - 6 Hours
Flash Point: Matt
Over Coat : Liquid
: 30 ْc
: After 12 HoursShelf Life : One Years in Sealed drum
Storage : Under Shade. Keep away from direct Sun Light and freezing Condition, clean, cool and dry place.
Surface Preparation : The surface to be painted must be clean by removing Rust, Mill Scale by wire brush. For better protection of Metals in many cases Mechanical Cleaning and sand blasting is recommended. Finally surface should be dry, clean and free from Dirt, oil grease and other contaminations. Apply 1 to 2 Coat of RED OXIDE PRIMER on prepared surface.
Packing : 20 Ltrs Drum
Application : By Roller, Brush or Spray. Stir well before use.
Thinner : Inter Thinner. After application clean the tools immediately with White Spirit.
Thinner Ratio : 15% to 20% by volume for Spray.
10% to 15% by volume for Roller or Brush.
Precautions : Ensure good ventilation during Application and avoid Breathing mist.
Keep away from Children. Do not apply below 5 ْc and on wet surface.
Safety : Use Gloves, Mask during application. Follow the Standard Safety measures as required for Decorative Coating System
